SmartCalc
FinancialHealthHome & EngineeringMathematicsTime & DateConvertersEducationGeneratorsGeneral
  1. Home
  2. /General
  3. /Craft Projects
  4. /Scalloped Hem Calculator

Scalloped Hem Calculator

Free scalloped hem calculator: fit equal circular scallops to a straight hem, calculate compass radius and arc length, and mark starts and centres.

A scalloped edge repeats curved sections along a baseline. This planner fits a whole number of equal circular scallops into a straight, open hem length, adjusting their width so the repeat ends exactly at the baseline's endpoint.

Enter the baseline length without side seam allowances, a preferred scallop width and the depth from the baseline to the deepest point. The calculator chooses the nearest whole repeat count, then checks that the depth fits a minor circular arc no deeper than a semicircle.

Use the actual width to mark each start, centre and end along the baseline. The centre mark locates the apex horizontally; its depth is the entered depth. The radius supports compass construction, while the arc length describes the curved edge rather than the straight span. Test the design and finishing method on a sample.

mm

Open baseline span, excluding side seam allowances.

mm
mm

Perpendicular distance from baseline to arc apex; at most half the actual scallop width.

Calculated dimensions

Scallop count
10
Actual scallop width
100 mm
Circle radius
72.5 mm
Arc length per scallop
110.35 mm
Total curved edge length
1,103.47 mm
Width adjustment
0 mm
Example
A baseline of 1000 mm with desired scallop width 100 mm and depth 20 mm gives 10 scallops, each 100 mm wide. Radius is 100²/(8 × 20) + 20/2 = 72.5 mm. Each arc is approximately 110.346849 mm long, giving a total curved length of 1103.468494 mm. Width adjustment is 0 mm; the first scallop starts at 0, has its centre at 50 and ends at 100 mm.

Scalloped Hem Calculator

Printed:

Current parameters

Straight hem baseline length
1,000 mmOpen baseline span, excluding side seam allowances.
Preferred scallop width
100 mm
Scallop depth
20 mmPerpendicular distance from baseline to arc apex; at most half the actual scallop width.

Calculated dimensions

Scallop count
10
Actual scallop width
100 mm
Circle radius
72.5 mm
Arc length per scallop
110.35 mm
Total curved edge length
1,103.47 mm
Width adjustment
0 mm

https://smartcalc.top/en/scalloped-hem-calculator/

Layout diagram

Schematic only; not a full-size cutting template.

Scalloped Hem Calculator — Layout diagram

Marking positions

Scalloped Hem Calculator · mm
Scallop numberBaseline startBaseline centreBaseline end
10 mm50 mm100 mm
2100 mm150 mm200 mm
3200 mm250 mm300 mm
4300 mm350 mm400 mm
5400 mm450 mm500 mm
6500 mm550 mm600 mm
7600 mm650 mm700 mm
8700 mm750 mm800 mm
9800 mm850 mm900 mm
10900 mm950 mm1,000 mm
For a straight, open baseline and equal circular minor arcs. Side seam allowances, seam finishing, fabric shrinkage and extra trim for joins are excluded. Depth must not exceed half the actual width after the repeat count is chosen. The arc total is a geometric edge length, not a trim purchasing allowance. Janome's scallop construction reference provides sewing context; this planner's circular geometry and adjustable depth are explicit design assumptions, not a universal hem pattern.

Method reference Janome ↗ · OpenStax ↗

Frequently Asked Questions

Why does the actual scallop width differ from my preferred width?

The baseline must contain a whole number of repeats. The calculator rounds baseline length divided by preferred width to choose that count, then divides the baseline equally. The signed width adjustment shows actual width minus preferred width, so a negative value means narrower scallops.

Is scallop depth the radius or diameter?

Neither in general. Depth is the perpendicular distance from the baseline at the scallop centre to the arc's deepest point, also called sagitta. The radius is calculated from that depth and the actual width. Only at the semicircle limit does the depth equal the radius.

Can I enter a depth greater than half the scallop width?

No. This planner supports minor circular arcs through a semicircle, so depth must be at most half the actual width. A deeper shape needs another construction and is rejected here. Recheck this condition when the preferred width is adjusted to fit a whole repeat count.

Related Calculators

Bag Gusset Calculator

Free bag gusset calculator for a closed rounded panel: find the inset stitch-line perimeter, cutting strip dimensions and corner marking positions.

→

Matching Stitch Holes Calculator

Free stitch hole calculator for two open seam paths: match hole counts, compare actual spacing and list paired positions from endpoint to endpoint.

→

Box Pleat Calculator

Free box pleat calculator: divide usable fabric into equal pleats, find fold depth and take-up, and list four crease marks for every pleat cell.

→

Book Case Calculator

Free book case calculator for flat spines: size cover boards, spine piece and cloth, with joint gaps, turn-ins and panel placement coordinates.

→

SMV Calculator

Free SMV calculator for garment time studies. Calculate rated standard minutes with allowances for each sewing operation and total the garment SMV.

→

SmartCalc.top — Free online calculators. No registration required.

© 2026 SmartCalc.top