Free stitch hole calculator for two open seam paths: match hole counts, compare actual spacing and list paired positions from endpoint to endpoint.
Two edges can need the same number of stitch holes even when their measured seam lengths differ slightly. This planner chooses a shared interval count and spreads that count evenly along each edge, so every hole has a numbered partner.
Measure each open stitch path from the centre of its first hole to the centre of its last hole, following any curves. Enter a target pitch to choose an interval count near the mean path length divided by that pitch. Both endpoint holes are included.
Compare the two actual pitches, their difference and the length mismatch before marking. The table gives distances along each stitch path from its own starting hole. Equal counts help align the marks, but do not remove excess length or establish whether the materials can be sewn together without distortion.
Measure along the open stitch line, from first hole centre to last hole centre.
Use the same endpoint-centre measurement on the second open stitch path.
Selects the interval count; the actual spacing can differ on each edge.
Printed:
Schematic only; not a full-size cutting template.
| Hole number | Distance along A | Distance along B |
|---|---|---|
| 1 | 0 mm | 0 mm |
| 2 | 4 mm | 4.07 mm |
| 3 | 8 mm | 8.13 mm |
| 4 | 12 mm | 12.2 mm |
| 5 | 16 mm | 16.27 mm |
| 6 | 20 mm | 20.33 mm |
| 7 | 24 mm | 24.4 mm |
| 8 | 28 mm | 28.47 mm |
| 9 | 32 mm | 32.53 mm |
| 10 | 36 mm | 36.6 mm |
| 11 | 40 mm | 40.67 mm |
| 12 | 44 mm | 44.73 mm |
| 13 | 48 mm | 48.8 mm |
| 14 | 52 mm | 52.87 mm |
| 15 | 56 mm | 56.93 mm |
| 16 | 60 mm | 61 mm |
| 17 | 64 mm | 65.07 mm |
| 18 | 68 mm | 69.13 mm |
| 19 | 72 mm | 73.2 mm |
| 20 | 76 mm | 77.27 mm |
| 21 | 80 mm | 81.33 mm |
| 22 | 84 mm | 85.4 mm |
| 23 | 88 mm | 89.47 mm |
| 24 | 92 mm | 93.53 mm |
| 25 | 96 mm | 97.6 mm |
| 26 | 100 mm | 101.67 mm |
| 27 | 104 mm | 105.73 mm |
| 28 | 108 mm | 109.8 mm |
| 29 | 112 mm | 113.87 mm |
| 30 | 116 mm | 117.93 mm |
| 31 | 120 mm | 122 mm |
Method reference Weaver Leather Supply ↗
An open path has a hole at the start and another at the end. Thirty gaps between consecutive holes therefore need 31 holes. A closed loop joins back to its first hole, so its counting rule is different and is outside this planner.
Only if the resulting actual pitch agrees with the tool. The target pitch selects a common interval count, then each path is divided evenly, which can change the spacing on either side. Check both actual pitches before using a fixed-spacing iron or chisel.
Not by itself. A small difference repeated over many intervals can still leave substantial excess length. Review the length difference and mismatch percentage together, then test the proposed join with the actual material. The calculator provides no pass/fail tolerance for easing or stretching.